How to Install a Matte Shower Head in your Bathroom?

0
76

To determine whether or not you require a new shower head, you must consider several factors, the most important of which is whether or not the spray is leaking or is not performing as it should be. The good news is that putting in a new matte black shower head is just as simple and basic as switching out a light bulb if you follow the specific instructions that we have provided.

You may create the impression that you’ve made some efforts toward modernizing your appearance by installing a shower head that has a matte surface. It is one approach to do it. These are the procedures that need to be taken for you to install a matte black shower head effectively:

Take Off the Existing Shower Head:

Even though it may seem like something that should go without saying, you should ensure that the shower is turned off before you start with the task at hand. Instead of turning off the water at the mains, all that is required is a simple modification to the settings on the shower itself. It is not necessary to turn off the water at the mains. The next paragraph will discuss the actions that need to be taken to remove the shower head. To remove the old shower head from the shower, turn it so that it is facing counterclockwise at the place where it attaches to the shower arm or hose. As a consequence of this, getting rid of it will now be feasible.

If the connection is too tight to turn by hand, you may use a wrench or locking pliers to obtain a better grasp on it so that you can turn it by hand. However, you shouldn’t need any specialized equipment to do this operation.

Wipe Off the Shower Arm as well as the Hose:

After removing the old shower head, you need to thoroughly inspect the shower arm or hose connection to look for any symptoms of corrosion, accumulation of dirt, or limescale, and then thoroughly clean it. Pay particular attention to the rubber washer that can be found inside, and if there are any signs that it has been damaged, replace it with a brand new washer. If the washer does not show any damage, you may disregard this step.

Apply Plumber’s Tape:

This step is optional, but doing so offers an additional layer of protection against leaks and should, in the long run, make the junction simpler to dismantle if it does not already have one. This step is essential when the connection does not have a rubber seal because it serves as a safety measure. Your collection of do-it-yourself equipment would benefit greatly from adding plumber’s tape, also known as Teflon tape or thread seal tape. If you are the type who likes to take safety measures wherever feasible, this would be a perfect purchase. This thin piece of white tape was designed expressly to create a watertight seal when applied to threaded connectors. The explanation, as mentioned earlier, provides insight into the thinking that went into its development.

If you have never worked with plumber tape before, you may find a lot of helpful tutorials to watch on YouTube. It is because you need to wrap the tape in the right orientation, which is the other way around from how the pipe will be twisted when you attach the head to the shower arm. The reason for this is that you need to connect the shower head to the shower arm. You should rotate the shower head clockwise if you attach it to a shower arm or hose. If you have never used plumber’s tape before, it is highly recommended that you look for a video on how to apply it on YouTube properly. You may fasten the free end of the tape by wrapping four or five times of the tape around the male threads located on the pipe’s exterior.

Screw on the Matte Shower Head:

After that, all that is left to do is ensure that the matte black shower head is attached to the shower arm or hose in the correct location and then screw it on in a clockwise manner. After you have turned it in, until you cannot turn it any further, you may put away any tools you were using since it will be sufficiently tight then.

Test for Leaks:

Please turn on the shower while keeping a close watch out for any leaks that may have arisen after you have completed cleaning the connection site and ensuring that it is dry. After you have done this, turn off the shower. Wrapping a piece of kitchen roll or toilet paper around the joint can offer it more support. Alternatively, you might use a bandage. The liquid will instantly seep through the container and become visible on the paper if the container has even the tiniest crack.

Conclusion:

Installing a matte black shower head is the simplest, least time-consuming, and most cost-efficient option to make a change that has a noticeable influence on the appearance of your bathroom. In addition, it is one of the strategies that involve the least amount of complexity. You can enhance the look of your shower and its functionality, which will help you save water and reduce the amount you spend on utilities.